1) Remove register from floor and flip face down
2) Place GoVentGo Deflector Auto Close face down on flat surface
3) Slide register into the Deflector between cover and base (See Installation sheet Fig. #3)
4) To complete the installation, pull the Deflector frame over the vent collar
(See Installation sheet Fig. #4)
5) Turn register over and check that hinges are on top
(See Installation sheet Fig. #5)
6) Insert/Remove Print into the Deflector. Ensure 2” TAB is flipped on top by inserting finger into the opening and gently pushing the TAB over the top of the deflector cover
(See Installation sheet Fig. #6)
1) Slide Print into opening at the back of deflector.
2) When sliding the Print in, locate the louver tabs on the sides, the Print goes on top of the tabs. This allows a snug fit.
3) Ensure 2” rear TAB is flipped on top by inserting finger into the opening and gentle pushing the TAB over the top of the Deflector cover
(See Installation sheet Fig. #6)
1) Remove register from floor
2) Measure floor open, rounding to nearest inch dimension
Example: 4x10 or 2x12
1) Remove register from floor
2) Measure floor open, rounding to nearest inch dimension
Example 4x10 or 2x12
1) Adjust register louvers, making sure they are in the open position (See FAQ #8)
2) Remove register louvers to get maximum air flow (See FAQ #10)
3) Remove deflector louvers (See FAQ #9)
4) Remove deflector Prints (See FAQ #2)
5) Your H-VAC System may not have enough feet per minute (FPM) air flow to properly operate your Vent Deflector Auto Close
Adjust register louvers to the maximum opening (See FAQ #8)
1) Remove deflector from register and place face down
2) Find louvers inside of deflector, place left and right index finger on louver and gently adjust left or right opening or closing for more or less scent opening
Using tab on Register louvers, ensuring your register louvers are in the most open option
1) Remove Deflector from register and place face down
2) Locate Deflector louvers inside the cover, gently remove louvers
Remove register from your floor. Use a pair of plyers and twist register louvers off the body of the register
1) Standard prints come in one maximum size
2) You will cut the new PRINT using the original inserted paper as a template
3) Lay the template on the Print
4) Using a pencil, draw a light line around the template
5) Cut the Print on top of the pencil line
6) Insert your new Print into your deflector. Do NOT put more than one print in the deflector. It is designed to lift with only one Print inserted.
1) Standard prints come in one size, you cut them to fit into your deflector.
2) You will cut the new PRINT using the original inserted paper as a template. Do NOT put more than one print in the deflector. It is designed to lift with only one Print inserted.
1) Register louvers may be closed, open register lovers to maximum position
(See FAQ #8.1: How to: Adjusting Register louvers)
2) Hinges may not be in the proper position, hinges need to be on the top of the register
(See FAQ #1.3: How to: Install Deflector onto your register)
3) You may have to heavy of Prints in deflector, for best results use goVENTgo prints or no prints
(See FAQ #2.6: How to: Install Prints into Deflector)
4) You have more than one Print in the deflector exceeding the maximin weight for deflector to lift properly
(See FAQ #2.6: How to: Install Prints into Deflector)
5) You may not have an original Print from GoVentGo
6) Your H-VAC System may not have enough feet per minute (FPM) air flow to properly operate your “Vent Deflector Auto Close”
(See FAQ #6: How to: increase air flow from your register)
Ensure that the back tab is positioned to the top of the deflector
(See FAQ #1.6: How to: Install Deflector onto your register)
Rear tab may not be positioned to the top of the register.
(See FAQ #1.6: How to: Install Deflector onto your register)